HDPE Pipes: Specifcations. Specification: IS with latest amendments. Material Grade PE All dimension are in mm. OD PN PN 4. PN 6. PN 8. Dinesh Irrigation Private Limited offering Is HDPE Pipes in Jhotwara, Jaipur , Rajasthan. Get contact details, address, map on Indiamart. | ID: We are leading manufacturer of HDPE pipes as per IS The best quality raw materials are procured to offer the pipes meeting the highest quality.
|Published (Last):||9 January 2014|
|PDF File Size:||7.84 Mb|
|ePub File Size:||6.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
For guidance and use of random number tables, IS Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments. Find more suppliers in Mumbai Hdpe Tube in Mumbai. Narainswami Alternate Shri S. This standard was first published in and revised inand Nominal diameter Maximum out of square DN of pipe end mm mm 16 to 75 2 90 to 3 to 4 to 5 Above 7 Page 9, Annex A, A-l — Substitute the following for the existing clause: No part of these publications may be reproduced in any form without the prior permission in writing of BIS.
Full text of “IS high density polyethylene pipes for potable water supplies”
Standards are also reviewed periodically; a hspe along with amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision. Sinha Alternate Shri O.
The temperatures, duration of test and induced stresses for the test shall conform to those specified in Table 6. The number of significant places retained in the rounded off value should be the same as that of ndpe specified value in this standard.
For coiled pipes, however, re-rounding of pipes shall be carried out prior to the measurement of ovality. Patel Alternate Dr H. Full text of ” IS View Contact Call Seller Now.
The test pieces shall be kept in the oven at the temperatures and for the periods specified below: For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2: The lot shall be pies to have satisfied these require- ments, if the number of defectives found in the cumula- tive sample is less than or equal to the corresponding acceptance number given in col 5 of Table 7; otherwise iiOi.
The details of conditions under which a licence for the use of the Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards.
Is 4984 HDPE Pipes
Nature of Business Manufacturer. Nominal Diameter DN 1 16 20 25 32 40 50 63 75 90 PN2. A pipe failing to satisfy any of these requirements shall be considered as defective. All the pipes in each of the sample size shall be tested for compliance in the requirements for hydraulic characteristics 8.
Product Description Being the leading names in the industry, we offer our clients an exceptional range of HDPE Plastic Pipes that are durable in nature and are sturdy in construction.
The lot shall be deemed to have satisfied these requirements, if the number of defectives found in the first sample are less than or equal to the corresponding acceptance number given in col 5 of Table 7. Regarding guidance for laying and jointing of polyethylene pipe, including storage and handling, a reference may be made to IS Part NOTES 1 The outside diameter shall be measured at a distance of at least mm from the end of the pipe.
IS 4984: high density polyethylene pipes for potable water supplies
The test pressure p shall be calculated as follows from the minimum dimensions given in the Table 3 or 4 or 5, as the case may be and the corresponding induced stress values given in Table 6. All pieces are required to be tested. Phadnis Alternate Shri S.
Part 1 1 Laying and jointing polyethylene PE pipes’. If any of the samples fails in the repeat tests, the typeof pipe shall not be approved. Our entire product range is well-tested. Legal Status of Firm Private Ltd.
Page 2, clause pipse. The lot shall be considered to have met the requirements of these tests, if none of samples tested fails.
However, occasional rise in temperature as in summer season with concurrent corresponding reduction in temperature during night has no deleterious effects on the life and working pressure of the pipes. The carbon black content in the material shall be within 2. A mark shall be scribed on the external surface hepe 50 mm from pipss end of the test pieces in the axial direction of pipe, in the case of complete section of pipe, the mark shall be scribed around the whole circumference.
The test showing failure within a distance equivalent to the length of end cap from the end shall be disregarded and the test repeated.